Cost-effective CWDM SFP transceiver 1000Base-ZX 1G (1.25Gbps/2.5Gbps) OC-48 CWDM SFP Singlemode 1270nm-1610nm up to 80km compatible CWDM-SFP-xxxx

Cost-effective CWDM SFP transceiver 1000Base-ZX 1G (1.25Gbps/2.5Gbps) OC-48 CWDM SFP Singlemode 1270nm-1610nm up to 80km compatible CWDM-SFP-xxxx

CWDM SFP 80KM 1.25Gb/s CWDM Single-mode SFP Transceiver(SP-Cxx1G-ZXDx)PRODUCT FEATURES ● Up to 1.25Gb/s data links ● DFB laser transmitter and PIN photo-detector ● Up to 80km on 9/125µm SMF

Product Details

CWDM SFP 80KM
1.25Gb/s CWDM Single-mode SFP Transceiver(SP-Cxx1G-ZXDx)


PRODUCT FEATURES
●  Up to 1.25Gb/s data links
●  DFB laser transmitter and PIN photo-detector
●  Up to 80km on 9/125µm SMF
●  Hot-pluggable SFP footprint
●  Duplex LC/UPC type pluggable optical interface
●  Low power dissipation
●  Metal enclosure, for lower EMI
●  RoHS compliant and lead-free
●  Single +3.3V power supply
●  Support Digital Diagnostic Monitoring interface
●  Compliant with SFF-8472
●  Case operating temperature: 0°C to +70°

APPLICATIONS
●  Switch to Switch Interface
●  Gigabit Ethernet
●  Switched Backplane Applications
●  Router/Server Interface
●  Other Optical Links


PRODUCT DESCRIPTION
CWDM SFP 80KM , Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA). The transceiver consists of five sections: the LD driver, the limiting amplifier, the digital diagnostic monitor, the DFB laser and the PIN photo-detector .The module data link up to 80KM in 9/125um single mode fiber.
 The optical output can be disabled by a TTL logic high-level input of Tx Disable, and the system also can disable the module via I2C. Tx Fault is provided to indicate that degradation of the laser. Loss of signal (LOS) output is provided to indicate the loss of an input optical signal of receiver or the link status with partner. The system can also get the LOS (or Link)/Disable/Fault information via I2C register access.


Specification of Transmitter

图片1.png


Specification of Receiver

图片2.png


Digital Diagnostic Functions
The CWDM SFP 80KM transceivers support the 2-wire serial communication protocol as defined in the SFP MSA. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications.

The standard SFP serial ID provides access to identification information that describes the transceiver's capabilities, standard interfaces, manufacturer, and other information.

Additionally, this SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage .It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range.   

The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement.    

The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver.  

The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially.

Digital diagnostics for the SF-CXX12-80D are internally calibrated by default

We cater to customers' needs, welcome to wholesale cwdm sfp 80km with our factory through our website.

Previous:No Information Next:CWDM SFP transceiver 1000Base-CWDM 1G (1.25Gbps/2.5Gbps) OC-48 CWDM SFP Singlemode 1270nm-1610nm up to 120km compatible CWDM-SFP-xxxx

Inquiry

You Might Also Like